Daftar Situs Slot Gacor Maxwin Online Resmi Terbaik Hari Ini

Kelebihan lainnya Ketika anda bergabung dengan situs Slot5000 sebagai situs deposit pulsa terbaik di Indonesia yaitu Anda dapat mendepositkan saldo ke dalam akun permainan dengan modal yang kecil. Pemain yang akan melakukan deposit via bank, anda dapat mengikuti caranya dengan meminta nomor rekening kepada pihak livechat. Setelah itu anda bisa langsung melakukan transaksi minimal deposit 10rb. Setelah anda berhasil melakukannya anda bisa langsung menginfokan kepada pihak live chat serta memberikan buktinya. Contact with live components may cause death, serious injury or painful electrical shock. EA 5000 Security 3.4.3 Safety instructions: electrical equipment Lethal voltages may occur in the device! The analysis system may only be set up, mounted and installed by the Analytik Jena AG customer service department. Function and design multi EA 5000 Function and design multi EA 5000 basic module The multi EA 5000 analysis system is modular and can be adapted to each measuring tasks by combining it with different detectors and sampling modules. Function and design multi EA 5000 4.2.2 Manual Boat Drive (MBD) The MBD is used for the manual transfer is samples on the sample boat to the combus- tion tube. EA 5000 Function and design Sample feed Liquid/LPG/gaseous Sample feed Solid/liquid/LPG/gaseous C/N/S analysis Dryer Flame sensor Quartz glass boat Cooled sample port Cl analysis – (EOX/TOX/AOX) Coulometer Figure 1 Operating modes of the multi EA 5000 4.1.1.2 Sample Digestion TS, TN, TC, TX and EOX Sample digestion to determine TS, TN, TC, TX and EOX can be performed in vertical and horizontal operation mode.

EA 5000 Function and design Figure 2 Front view in vertical operation mode 1 Ventilator 2 Control electronics 3 Membrane dryer unit 4 Tilt device 5 Pump connection for N/S/C mode 6 Combustion furnace 7 Knob for tilting the furnace Horizontal device Furnace in horizontal installation position ¡ Function and design multi EA 5000 4.1.2.2 Electrical components, display elements and connections Internal device control The control electronics are found on the rear of the basic module behind the panel when viewed from the front. Function and design multi EA 5000 Gas supply control The composition of the gas mixture for optimum gas digestion is controlled via the flow management system (FMS). Digestion is performed in two phases. Function and design multi EA 5000 EC/OC Digestion for EC/OC determination is performed in horizontal operation mode. The user manual contains descriptions of the design and operation of the multi EA 5000 and provides personnel experienced in analysis with the necessary information for the safe handling of the basic module and its components. Security multi EA 5000 Security For your own safety and to ensure error-free and safe operation of the device, please read this chapter carefully before commissioning.

Security multi EA 5000 To prevent health damage, the following must be observed when moving the device in the laboratory (lifting and carrying): ¡ For safety reasons, two persons are required to transport the device who must hold the unit by either side of the equipment. Cl module. For this reason, the measuring gas lines to this module must be dis- connected before closing the argon gas supply. In the first process phase, the OC content adsorbed on the filter samples is thermally desorbed in a pure argon flow. EA 5000 Security When closing the argon gas supply, a return of the acid used can occur in the ¡ Security multi EA 5000 3.4.5 Decontamination after soiling Observe the following: The operator is responsible for carrying out suitable decontamination should the ¡ EA 5000 Security Warning sym- Meaning Comment Caution (GHS07) On the absorber and the chemical ozone decomposer of the CLD 5000 On the chemical ozone decomposer of the MPO 5000 The cartridges contain hazardous sub- stances. Observe all safety instructions listed in this user manual and all messages and infor- mation displayed on the monitor by the control and analysis software.

The control electronics provides the power supply and control of the individual components and the communication with the control PC and other con- nected system modules. EA 5000 Installation and commissioning Installing and commissioning the analysis system WARNING Danger due to incorrect commissioning ¡ 4.1.2.4 Combustion system A resistance-heated combustion furnace for digestion temperatures of 700 to 1100 °C is used in the basic module. The membrane dryer is mounted on the furnace. EA 5000 Function and design 4.1.2.5 Measuring gas dryer Measuring gas is dried in accordance with the measuring method: To determine TS, TN, TC, EC/OC via membrane dryer: ¡ To increase drying effectiveness, purge gas (O ) is drawn through the membrane dryer with a pump. EA 5000 Function and design Figure 9 Connections for the auto-protection valve assembly and transfer line 1 Toggle switch for opening and clos- 2 Transfer line heating connection ing the pneumatic seal in the auto- protection valve assembly 3 Valve assembly connection 4.1.2.3 Gas supply/hose diagrams Hose diagrams The connection between the individual components is made with labeled hoses. Function and design multi EA 5000 Gas connections at the rear of The gas connections are located on the rear of the device.